What're your thoughts with regards to Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is additionally a reasonably hard job. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need a helper to leave the old bathtub and embeded in the new one. Ensure you have qualified on your own for the task and are comfortable trying it. Instead of working with a professional to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will certainly aid you install a brand-new bath tub in your bathroom if you have actually already acquired a new tub and don't need to change the plan of your previous water system pipes.
Your devices and also material list should comprise the following:
Planning for the Setup
First of all, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the called for setting. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bathtub till the spirit level checks out degree.
To set up taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub should wait up until the bathtub has actually been used at least when as this will resolve it right into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in place in between the tap and also the sink. Protect the faucet in position with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former kind must be connected to the faucet ends first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break an inflexible seal, causing the water to pass through the wall surface between the bathroom and also the tiling, causing problems with wetness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub is in usage. The sealant can fracture fairly early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is advisable to fit the floor tiles making use of waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks for taking the time to read our content. Kindly set aside a second to distribute this page if you enjoyed reading it. I thank you for reading our article about Installing A Bathtub.
Immediate relief, just a call.